Quick answer: Brakes are serviced by axle. Replace the pads on both the left and right wheels of an axle at the same time, and if one rotor on that axle needs replacing, replace both. The front and rear axles are separate jobs and can be done at different times. Mismatched parts side to side can make the vehicle brake unevenly and pull.

What “replace in pairs” means

“Pairs” refers to the two wheels of one axle, not to all four wheels:

Part Replace together Source
Brake pads All pads on the axle: inner and outer, left and right Brembo: pads “must always be replaced throughout the vehicle axle”
Rotors Both rotors on the axle, even if only one is below the minimum Brembo
Pad wear sensors Replace with the pads; if one has triggered, replace all the pads on that axle HELLA, Brembo
Front vs rear Judged separately; each axle is replaced when it needs it Wagner: the front brakes do most of the work

Why pads are replaced per axle

The left and right brakes on an axle are meant to grip with the same force. New pads on one side and part-worn pads on the other are a mismatch in thickness and condition. A pad fitting guide from AutoZone South Africa puts it bluntly: if only one set of pads on an axle is replaced, the vehicle will brake unevenly and pull to one side.

Brembo’s fitting instructions make it a rule: the pads must be replaced for each caliper on the axle. They also say that if one pad’s wear indicator has triggered, all the pads on that axle are to be replaced. Check each listing to see what the set includes.

When you take the old pads out, compare them. If one side is much more worn than the other, or the inner and outer pads differ a lot, something is binding. Delphi links outer-pad wear to seized slides or guide pins and inner-pad wear to a caliper piston that isn’t returning. Fix that at the same time, or the new pads will wear the same way. Our guide on when to replace brake pads covers these wear patterns.

Why rotors are replaced per axle

Brembo says rotors must be replaced on both sides even if only one of the pair is below the minimum thickness. The reasoning is the same as for pads: both sides of the axle should brake the same way.

Our guide to brake rotors vs brake pads explains when machining is worthwhile and when a rotor has to be replaced.

Front and rear are separate jobs

Wagner explains that braking shifts the vehicle’s weight forward, so the front brakes do most of the work. As a result, front and rear pads often wear at different rates. Measure each axle and replace what has reached its limit. There is no need to replace good rear brakes because the fronts are worn, or the other way around.

What about drum brakes?

On vehicles with drum brakes, inspect both wheels of the axle together and check both drums against the limit in the service manual. If a wheel cylinder is leaking, inspect the one on the other side closely too. NAPA’s Know How notes that it is fairly common for both to start leaking at around the same time.

When one side wore out first

A brake that wears out on one side only is a symptom. Wagner says a car that pulls to one side under braking has brakes that are not applied evenly, which can mean a pad that doesn’t contact the rotor or one that doesn’t retract. Before fitting new parts, have the calipers, slide pins and boots checked. Brembo’s instructions say to check the caliper and its sliding and guide parts for wear, replace corroded guide bolts and damaged dust boots, and replace a caliper that shows fluid contamination or other damage.

Doing the job

  1. Confirm the parts for your exact vehicle and axle. Front and rear parts usually differ.
  2. Support the vehicle securely on jack stands.
  3. Work on one side at a time and use the untouched side as a reference, as Brembo recommends.
  4. Follow the service manual for the procedure and all torque values.
  5. Press the brake pedal to seat the pads before moving the car, and bed the new parts in as the pad, rotor or vehicle maker instructs.

If you are unsure about any step, or the car was pulling before the job, have a qualified technician inspect the brakes.

Parts you’ll need

Browse drums and rotors, disc brake pad sets and drum brake wheel cylinders. Examples:

Part Brand Listed for Price
Fremax BD4207 Disc Brake Rotor Fremax INFINITI, Nissan $36.15
Asianautos ACR1393 Premium Ceramic Disc Brake Pad Set Asianautos INFINITI, Nissan $24.32
Fremax BD4115 Brake Drum Fremax Toyota $56.76
Beck/Arnley 072-1830 Wheel Cylinder Beck/Arnley Honda $15.20

Prices may change; the product page shows the current price. “Listed for” shows the makes on each listing, not that two parts fit together; check the full fitment list for your year, model and axle. Check whether a rotor or drum listing is for one piece or a pair, so you order enough for both sides. If anything is unclear, send us your VIN and our team will confirm what you need.

Standard shipping is free to the lower 48 states with no minimum order, and in-stock orders placed before 2:00 PM ET usually ship the same business day.

FAQ

Can I replace just one rotor if the other is fine?

Brembo says no: both rotors on an axle must be replaced even if only one is below the minimum thickness.

Do I have to do all four wheels at once?

No. Pairs means both sides of the same axle. Front and rear are checked and replaced separately.

Can I put a different brand of pad on each side?

No. Replace the pads on both sides of the axle with the same set so they grip the same way.

For the full picture of pads, rotors, sensors and hardware, read our brake repair guide.

Safety note: Brakes are safety-critical. This guide is general and may not match your vehicle. Follow your vehicle’s service manual and have a qualified technician inspect the brakes if you are unsure. US Automotives is an independent retailer and is not affiliated with any vehicle manufacturer.